Just How to Set up a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Just How to Set up a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Blog Article
Almost everyone has their personal beliefs about How to Install a Bathtub.
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough task. If the old bathtub is readily obtainable, the job can relocate quickly; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the work as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to consider utilizing one before you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will aid you install a brand-new bath tub in your restroom if you have actually currently bought a brand-new bathtub and do not require to change the arrangement of your previous water system pipes.
Your tools and also material checklist must comprise the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bath ought to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to avoid strain on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its last placement.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the tub until the level reviews level.
To set up taps, fit all-time low of the furthest versatile tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the water system and inspect all joints and also new pipework for leakages and tighten them if needed. Fill up the bath tub and likewise inspect the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been used a minimum of once as this will resolve it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washers are in location in between the faucet and also the sink. Secure the faucet in position with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The former type should be linked to the faucet ends first, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to break an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub remains in usage. The sealer can break fairly very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is recommended to fit the tiles using waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about Tools You Need to Install a New Bathtub ? Create feedback down below. We would be delighted to find out your opinions about this blog post. We are looking forward that you visit us again later on. Loved our piece? Please share it. Let others find it. Thank-you for your time invested reading it.
Book Inspection
Report this page